20AC 1/8 Flow. Compression sizes of 5/32" and 1/4" OD poly tubing.
The GSBV series is a one-way brass garden hose ball valve.
The SSRC series is a 304 stainless steel NPT threaded connector and reducing connector. It is also available in 316 stainless steel.
The AFH series plastic female NPT to multi-barbed adapter fittings are available in nylon, black polypropylene, or PTFE materials in sizes ranging from 1/4 inch to 3/4 inch Barbs.
The BSL series are detent panel mount 5-way ball valves in 10-32, 1/8 inch female NPT, 1/4 inch female NPT, 1/8 inch male NPT, or 1/4 inch male NPT with EPDM seals and 500 psi.
These Cartridge Insert Valves can be installed into tubing lines or glued into manifolds. The optional housing materials are Nylon, Polypropylene, Acrylic, Acetal, PVDF, and Polycarbonate. Springs are 316 Stainless Steel or Hastelloy® (1/2 psi). O-Rings are of Buna-N, EPDM, FKM, Silicone and Kalrez. Available sizes are 1/4″, 5/16", 3/8", 1/2″, 5/8" and 3/4" OD. Standard crack pressure for all valves except 3/4″ OD is 3" H2O 0.1 psi, 5 psi, or 1.5 psi.
DMF Series is an aluminum Flow Control Valve for air and oil. Its maximum working pressure is 250 psi, and its temperature range is -40ºF to 250ºF. Also, the sizes available are 1/4-28 Male/Female and 1/8”, 1/4″, 3/8”, and 1/2” Female NPT. These valves control flow in one direction and allow free flow in the opposite direction.
MBBV series is a forged 3-way ball valve that offers flow options in both directions as well as allowing unimpeded flow when the handle is placed at a 45º angle. In addition, the temperature rating for this valve is 0-230 ºF. Also, the pressure rating of this ball valve is 600 WOG.
Double-grip, ratchet-style Hose Clamps are made from a tough black Nylon material that can withstand pressures up to 100 psi. There are sizes available to fit hose OD ranging from 0.22" to 2.97" (5.6mm to 75.4mm). The clamps can tolerate temperatures from -40º F to 340º F. They also have high chemical resistance including gasoline, oils, and most solvents.
These female NPT barb fittings are available in nylon and polypropylene. Sizes available include 1/8" FNPT to 1/8" Barb, 1/4" FNPT to 1/4" Barb, 1/4″ FNPT to 1/8" barb and 1/8" FNPT to barb.
AML series are MNPT by triple barbed elbows. This elbow is molded of NSF listed natural nylon or black polyethylene. Barbed fittings over one inch are not offered in polyethylene. Optional materials include black nylon, FDA listed natural polypropylene, and FDA listed black polypropylene. Fittings over 1 inch are not available in polyethylene.
AO-IG series is a thread-to-barb fitting made of FDA-approved polysufone with an integral precision orifice. The threads are 10-32 inch male UNF threads and the barbs are either 1/8 inch or 1/16 inch. The maximum operating pressure is 100 psi.
The A-R series are standard single-barbed adapters. These adapters have 10-32 inch and 1/4-28 inch male UNF threads, and 1/16 inch NPT male threads. In addition, the materials available are: natural and black nylon, polypropylene, PVDF, and high-density polyethylene.
Our polypropylene fittings are made from a medical grade, gamma serializable polypropylene offering a greater chemical resistance.
These couplings are available in both grey polypropylene and almond-colored polypropylene.
186-2 Series is a Brass Barb Fittings are designed to fit 0.073 holes using a Loctite adhesive.
1/16 inch Barbed Brass Bondable Insert
This series of brass connectors is composed of straight connectors, elbows, tees, and crosses. The working temperature range is – 40 ºF to 160 ºF. The straights, tees, and crosses have equal barb sizes. The elbows are both equal and reducing. These fittings are designed for use with hose clamps.
The BI series are brass or 303 stainless steel bite-style barb inserts for manifold applications. Available in 1/16 inch, 0.078 inch, 3/32 inch, 1/8 inch, 5/32 inch, 3/16 inch, 1/4 inch, 5/16 inch, and 3/8 inch.
The ISR series is a brass thread insert.
Pneuline Supply, Inc. manufactures these low-pressure lab disconnects made from either polyethylene or polypropylene which are used in laboratories for vacuum applications, low-pressure lines, water lines, and inert gases. They can be purchased with a Fluorocarbon (FKM) or EPDM disc check valve, or with a porous polyethylene filter. A unique pick-up tube line assembly for use in drawing air or water from containers is also available.
They are available with a filter.
Male luer by thread adapter. The bottom sealing threads are available in both UNF and NPT. The integral lock ring luer is available in white and black Nylon, black Acetal, black and natural Polypropylene, clear Polycarbonate, and PVDF. The rotating lock rings are available in 7 colors of Nylon over Polypropylene or PVDF.
The BCE series is a sweep elbow with bite-style barbs to hold the tubing securely and prevent slipping or pulling off. It is an excellent fitting to use with polyurethane or polyethylene tubing. It is made in brass, nickel-plated brass, or 303 stainless.
Garden hose plug with female 3/4" NPT threads. Made of standard Nylon or Black Polypropylene.
The MGSP Series is a brass male garden hose square Plug.
The FGFGS series is a Brass FGHT by FGHT swivel connector. A non-swivel option is available.
The BCX and the BCXR series are bite-style cross fittings. The BCXR series is the reduced version of the BCX series. These crosses have single sharp barbs to securely hold the tubing from slipping or pulling off. They are excellent fittings for use with polyurethane or polyethylene tubing.
Single garden hose shutoff has an ABS body, ball, and handle. It has a Zinc plated steel screw and Buna-N seal. It flows from female to male. Maximum pressure is 80 psi, designed for water pressure. Maximum temperature is 125ºF. Available in blue, green, or yellow.
The GHME Series are male garden hose threads by MNPT elbows. This series is made of Nylon. Available MNPT sizes are 3/8 inch, 1/2 inch, and 3/4 inch.
GHT Series is a versatile Male Garden Hose designed with two barbed fittings, available in durable Nylon or black Polypropylene materials. This series offers a range of sizes, including 3/8-inch, 1/2-inch, 5/8-inch, and 3/4-inch barbs. Ensuring compatibility with various garden hose applications. The robust construction of Nylon and Polypropylene provides excellent resistance to wear and tear, making these fittings ideal for both residential and commercial use.
FME Series is a female-to-male street Elbow. In addition, this elbow is made of natural Nylon or Polypropylene.
TBB Series is a high-quality brass tube-to-tube connector with a sapphire orifice, designed for durability and reliability in various applications. This connector features a precision-engineered sapphire orifice, which ensures optimal flow control and resistance to wear. The connector is equipped with 1/16-inch barbs, providing a secure and leak-free connection for tubing. Its robust construction and superior materials make it an excellent choice for both labratory and industrial use.
TL Series, a meticulously crafted plastic thumb latch, seamlessly combines form and function. 5/32 size available.
The MCC series is a chrome-plated brass ferrules compression fitting. The pressure range is vacuum to 100 psi and the working temperature range is -40 ºF to 180 ºF. Tubing options for use with this fitting are Polyethylene, Polyurethane, and PVC.
Synthetic sapphire orifice pressed in a nylon housing of 0.125" or 0.134" OD.
Push-to-connect cross connectors available in acetal are used to join tubing of polyethylene, brass, or copper. Sizes range from 3/8 inch OD size only. Gray or white acetal are NSF and FDA-approved and have Buna seals for use in air, gases, and potable water applications. Also available with double O-ring EPDM seals. For other options see our PUCX series push-ins.
SCMS Series is a miniature Hose Clamp that is 5/16" wide and made of 301 Stainless Steel. It has a 1/4″ hex-slotted 410 Stainless Steel screw. Also it can be used for agricultural, industrial, and automotive applications. The diameter range is 5/8" to 1-3/4".
This check valve is made of either white polypropylene, natural Nylon, or black or natural Polyvinylidene Fluoride (PVDF). It is available with a Buna-N, EPDM, or Fluorocarbon (FKM) seal. It has a 302 stainless steel spring. The cracking pressure is 0.25 or 1 psi. The maximum pressure is 125 psi and the maximum operating temperature is 140ºF. The ports can be single or multi-barbed.
The SSES Series are 304 Stainless Steel 90º elbow hose barb splicer fittings. These elbows are intended to be used with hose clamps or similar clamps. Working temperatures are from -40º F to +160º F. Maximum working pressure is 150 psi. Available in barb sizes of 1/4 inch and 3/8 inch.
PCR series tube racks come with 5, 7, or 10 channels to accommodate OD tubing sizes of 1/4", 5/32", or 3/16" with the ability to be separated into smaller sections. In addition, the tube racks come in an assortment of colors with black being standard. Furthermore, they can be mounted with screws or purchased with an adhesive backing.
PV series is an acetal pinch valve that controls the flow through by flexing tubing from zero to full flow. Since the fluid being delivered never comes in contact with the valve, there is no fear of contamination. In addition, this is a long-lasting reusable alternative to other fluid delivery valves. Furthermore, the body has an easy-to-read metered scale on the side for ease of use.
The BE series brass 90º elbow bite-style connectors are fabricated with silver solder that complies with FDA, NSF, and medical grades VT lead-free and cadmium-free solder. Also available in 303 stainless steel. Included with the BE series is the BER series, which is the reduced version of the BE series.
TCC series plastic tube clips are available for 3/8", 1/4", or 1/2" OD tubing and are sold as a single clip of 6, 7, or 10 channels. Also, they can be mounted with screws on each end. Furthermore, they can also be cut for custom installations.
TCM series are straight connectors made of 316 stainless steel. One end is smooth for easy attachment of tubing and the other has male threads below a hex nut for tightening. Also, it has a working pressure of 290 psi and a temperature range of -4 ºF to 302 ºF. The sterilization temperature is up to 280 ºF. The O-ring is Viton®. BSPT is also available.
MV Series miniature Panel Mount Nickel-plated Brass Toggle Valves are Two-way normally closed or normally open, Exhausting or Non-Exhausting. Standard is 10-32 Female UNF outlet with 10-32 Female UNF inlet, 1/8 inch Male NPT, or 1/8 inch Female NPT inlet at the base. Seals are Buna, EPDM, or optional FKM. 1/8-inch ported and 1/16 inch barbed Air Pilot Valves with 35 psi activation are also available. Valves can be equipped with an actuator of either: a Toggle Momentary, or Toggle Detent, a Push Button, Ball, Roller, or Long Cam.
The PPF Series is a push-to-connect cap for use with all push-to-connect fittings to block a port. The body is PBT with a Buna-N O-Ring. This fitting is also available in metric sizes.
TCP series plastic multi-position clamps are made of Polyester for 1/4 inch, 3/16 inch, 5/32 inch, 1/2 inch, or 3/4 inch OD tubing. These units can be sterilized using Gamma, ETO, or Autclave. Multi-position only available for 1/2 inch and 3/4 inch sizes only
HCSS Series is a Bar stock Hex Socket Plug made of 304 or 316 Stainless Steel. It can be used with air, water, oil, natural gas or steam. Also, the maximum pressure is 300 psi at 72º F or 150 psi at 366º F for steam.
Push-to-Connect Straight Divider Wye connectors available in Acetal, Polypropylene, and Kynar® used to split or reduce tubing connections of Polyethylene, Brass, or Copper. Sizes range from 1/4 inch OD to 3/8 inch OD including reducing sizes. Available in 1 inlet to 2 outlets, or 1 inlet to 3 outlets. Gray or White Acetal are NSF and FDA-approved and have Buna seals for use in air, gases, and potable water applications. White Polypropylene with EPDM seals or PVDF with FKM seals. Maximum temperature 140ºF at 60 psi for Polypropylene.
The FGHMS Series are Nylon female Garden Hoses with Male NPT swivel fittings. Available MNPT thread sizes are 1/4 inch, 3/8 inch, and 1/2 inch.
G1 Series Pressure Gauge has an ABS case with a Brass movement and a dial size of 1". The Gauge is available in 30, 60, 100, and 160 psi. There is a 1/8" MNPT center back mount that can also accommodate a 10-32 male UNF fitting inside that 1/8" fitting. Also, the operating temperature for this gauge is 0ºF to 160ºF. The maximum supply is 50% over the gauge pressure range. Furthermore, his gauge is recommended for use with steam, air, oil, and water.
Our PSSV series, self-sealing check valves, are made from either polycarbonate or polypropylene housings with Barb connector sizes for 3/16 inch ID tubing or 5/16 inch ID tubing. The product is made in a class 7 clean room. The seal is a retractable silicone disk that prevents back-flow in several air and liquid applications making it an ideal option for the medical Industry for air applications including respiratory, ventilator, bio-pharmaceutical. The product can also be used with fluid applications for the medical devices. Designed for pressures under 50 PSI. All material are compatible with Gamma Sterilization 6 Mrads, and ETO Sterilization.
Nickel Plated Brass countersink plug vents will fit flush in any application: gearboxes, storage tanks, single-action cylinders. The Male NPT thread sizes are 1/8"-27, 1/4"-18, 3/8"-18, and 1/2"-14. A 40-micron sintered Bronze filter is standard but optional 10-micron and 90-micron are available. Maximum operating pressure is 150 psi and the operating temperature is 35ºF to 300ºF.
PUCX series is a union Cross push-to-connect fitting with four opposing, equal-sized ports made of polybutylene. This fitting is also available in metric sizes.
Push-to-connect female bulkhead union fitting with female NPT and BSPT threads. It is made of nickel-plated brass with PBT resin. The working pressure is 150 psi and the temperature range is 32 ºF to 140 ºF. It can be used with compressed air and inert gases.
The SCHB series is a cast 304 stainless steel Male NPT threads by barb adapter. Also available are barb to MNPT thread reducers. The available MNPT thread sizes are 1/4 inch, 3/8 inch, 1/2 inch, 1/8 inch, and 3/8 inch. The available barb sizes are 1/4 inch, 3/8 inch, 1/2 inch, and 3/4 inch.
The RBSS series is a 304 stainless steel hex bushing.
SSCX series is a stainless steel cross with equal female NPT threads. It is available in both 304 and 316.
The 304 stainless steel hex nipple with male NPT threads is a versatile fitting known for its corrosion resistance and durability. It is also available in 316 stainless steel, which offers even greater corrosion resistance, This makes it an excellent choice for industries where exposure to corrosive substances is common.
The SSFX series is a stainless steel union with female NPT threads. It is available in both 304 and 316.
TGF series is a PFA compression-reducing adapter with female NPT threads to a gripper ring. OD sizes range from 1/8 inch to 3/4 inch.
The FPC series are equal connectors, and the FPRC series are reducing connectors. Both series are available in natural nylon and black polypropylene. The female threads allow a connection to two male fittings. The female NPT threads range from 1/8 inch to 3 inches in both equal and reducing configurations. Reducing connectors 1 inch and above are not available in natural nylon.
The FEV series are brass female adapters with sharp barbs. The barbs are available at 60º, 90º and 120º on the flats of the hex. Female NPT thread sizes include 1/8 inch, 1/4 inch, and 3/8 inch. Barb sizes range from 0.170 inch to 1/8 inch.
The AT-R series are single-barbed by male NPT threads tee adapters. Available in black and natural nylon, glass-filled nylon, natural and white polypropylene, PVDF, and polyethylene that is NSF 51/61 listed. Thread sizes range from 1/8 inch to 1 inch. Barb sizes range from 1/4 inch to 1 inch.
The MEV series are brass MNPT thread with bite-style barbs at 60 degree to the flats. These elbows come in 3 different sizes of the angle between elbows - 60º, 90º and 120º. This series comes in MNPT thread sizes ranging from 1/8 inch to 3/8 inch and barb sizes ranging from 1/16 inch to 1/2 inch. Also available in nickel-plated brass and 303 stainless steel.
The HLB series are brass hexless 10-32 UNF Connectors available in 0.170 inch, 1/16 inch, or 1/8 inch barbs.
ME Series Brass male Elbow adapters with bite-style barbs ranging from 1/16 inch to 1/2 inch at 90º and 45º angles.
The MFA series consists of high-quality brass female-to-male connectors. They are designed to serve various threading standards including NPT, UNF, and BSPT. These connectors are engineered for durability, making them appropriate for a wide range of industrial applications where secure and leak-proof connections are needed.
AM-U series is a 1/4-28 inch UNF bottom sealing swivel fitting. It is available with polypropylene or PVDF interiors with a nylon encasement. The nylon comes in five colors: white, black, red, blue, or green. There are three barb sizes: 1/16 inch, 3/32 inch, and 1/8 inch
The T-R series is a standard industrial-grade, single barbed tee connector. There is a rib behind the barb to prevent the tubing from rotating. There is no parting line on the barb. This Tee is available in natural and black nylon, Natural and gray PVDF, polyethylene certified NSF 51/61, natural and white polypropylene, HDPE, and glass-filled black nylon. Equal barb connectors come in a range of sizes from 3/32 inch to 1 inch. The reducing barb sizes available for this series are 5/8 inch by 3/8 inch.
The CB Series Compression Bulkheads allow Air or Fluid lines to be passed through walls for a clean connection for use with tubing ranges of 1/4 inch to 7/8 inch Outside Diameter in tanks and service lines. Available in NSF approved Glass-Filled White Polypropylene, FDA and NSF approved Acetal (POM) for use with hot water applications, FDA and NSF approved Nylon and UV resistant FDA and NSF-rated PVDF. Provided with Poly gripper (except for 1/8 inch units) for us up to 220 psi.
The T series is a series of plastic single and multi-barbed tee connectors. This series is available in NSF-listed natural nylon, black polyethylene, and FDA-listed natural black polypropylene. Equal and reducing barb sizes ranging from 0.170 inches to 1-1/2 inches are available. Barb sizes over 1 inch are not available in polyethylene.
The SSBM series multi-barbed hose splicer fitting is made of 303 stainless steel and is available in straight barb sizes of 1/4 inch and 3/8 inch. The available reducing barb size is 3/8 inch by 1/4 inch.
These PBT plugs block off push-to-connect ports. The working pressure is 150 psi and the temperature range is 32 ºF to 140 ºF. For use with compressed air and inert gases.
The PSR series is a PBT stem reducer. Not for water applications, only air. The working pressure is 150 psi and the temperature range is 32 ºF to 140 ºF.
Compact straight fitting with two push-to-connect ports in opposite directions. The body is PBT resin. The working pressure is 150 psi and the temperature range is 32 ºF to 140 ºF. Suitable for applications involving compressed air and inert gases.
The ML Series are rotating male luers made of Nylon, Polypropylene, or Polycarbonate. Nut colors include black, red, and blue
